Accurate Revolver

The #1 community for Gun Owners of the Northeast

Member Benefits:

  • No ad networks!
  • Discuss all aspects of firearm ownership
  • Discuss anti-gun legislation
  • Buy, sell, and trade in the classified section
  • Chat with Local gun shops, ranges, trainers & other businesses
  • Discover free outdoor shooting areas
  • View up to date on firearm-related events
  • Share photos & video with other members
  • ...and so much more!
  • Melnic

    Ultimate Member
    MDS Supporter
    Dec 27, 2012
    15,282
    HoCo
    I'll be on the lookout for an Accurate Revolver for shooting single handed at 25 yards. I reload so I"ll be able to tune the load but just wondering what I should look for when going through gun shops for maybe an accurate used one?
    What models would be decent?
    I'm hoping I would luck into finding a used one that already has a trigger job.

    I have some 357 to do reloads but plenty of 38 too.

    Not in a rush but looking for guidance on what to look into and what to steer away from.
     

    trickg

    Guns 'n Drums
    MDS Supporter
    Jul 22, 2008
    14,597
    Glen Burnie
    There are also the classic S&W Models - the 19 and 27, or the 28 Highway Patrolman. Harder to find, but equal, if not better, than the 586/686.
     

    TheOriginalMexicanBob

    Ultimate Member
    Jul 2, 2017
    32,176
    Sun City West, AZ
    Most any Colt, Ruger or S&W revolver will do what you want. Most are more accurate than the shooter and rare is the one that won't be accurate enough. One of the most accurate revolvers I've fired was a S&W Model 64 heavy barrel...4" barrel and fixed sights and was incredibly consistent. On the PPC Course I shot 300 five straight times with it.

    Get the one that fits your hand best and balances well.
     

    joppaj

    Sheepdog
    Staff member
    Moderator
    Apr 11, 2008
    46,452
    MD
    My Ruger Blackhawk in 45lc is capable of greater accuracy than I am. The SA only trigger is very nicely weighted.
     

    Bisleyfan44

    Ultimate Member
    Jan 11, 2008
    1,758
    Wicomico
    Freedom Arms 83 or 97. Costly yes, but made with he highest level of precision. If it doesn't shoot well, it's you not the gun.

    But then again, my lowly 357 Blackhawk is quite accurate, enough for me anyway. And a whole lot cheaper.
     

    4g64loser

    Bad influence
    Jan 18, 2007
    6,381
    maryland
    Just my.02 (not a bullseye guy). I had a 66 that was a great shooter but my best results have been with N frame guns. I would not hesitate to use a .44 with lower pressure loads for one hand practice. The 27, 28 are the 357 versions. If you like a k frame, try to find a 66 or a 64 with adjustable sights. Find a .38 load (3.2-3.7gr Bullseye and a 148 wadcutters comes to mind) that shoots well and enjoy.
     

    Dovk0802

    Active Member
    Sep 20, 2017
    255
    DC
    Most any Colt, Ruger or S&W revolver will do what you want. Most are more accurate than the shooter and rare is the one that won't be accurate enough. One of the most accurate revolvers I've fired was a S&W Model 64 heavy barrel...4" barrel and fixed sights and was incredibly consistent. On the PPC Course I shot 300 five straight times with it.

    Get the one that fits your hand best and balances well.

    I also had a 64 that was a surplus cop gun; it was scratched up so bad on one side that I assume it got dragged across the asphalt. With regular wadcutters or SWCHP, someone better than me, could keep it to have six shots touching pretty much all the time out to 25yd. 20 something years ago, when I was even dumber, I made the mistake of leaving it in my car (in bag not ready to go) and was stolen in a smash & grab...:sad20:
     

    Biggfoot44

    Ultimate Member
    Aug 2, 2009
    32,881
    I'm not a Colt DA guy , so don't have a basis . But I've known plenty of S&W and both flavor of Ruger to do the 1.0in @ 25yd .

    It's less a matter of which model as the lock up, timing , throat , and forcing cone of specific gun .
     

    John from MD

    American Patriot
    MDS Supporter
    May 12, 2005
    22,733
    Socialist State of Maryland
    I'll be on the lookout for an Accurate Revolver for shooting single handed at 25 yards. I reload so I"ll be able to tune the load but just wondering what I should look for when going through gun shops for maybe an accurate used one?
    What models would be decent?
    I'm hoping I would luck into finding a used one that already has a trigger job.

    I have some 357 to do reloads but plenty of 38 too.

    Not in a rush but looking for guidance on what to look into and what to steer away from.

    It depends what kind of shooting you plan to do with it. I can tell you that you probably won't shoot too many .357 mags one handed before you realize that it isn't fun.

    If you plan to shoot paper, maybe you should look for a S&W Model 14. They are K frame revolvers and have been known for their accuracy. If you still want to shoot .357 periodically, then look for a six inch Model 686.

    Ruger GP revolvers are great utility guns but they aren't target pistols.
     

    28Shooter

    Ultimate Member
    MDS Supporter
    Sep 19, 2010
    8,206
    Baltimore, Maryland
    For one-handed shooting, any older K-frame S&W with adjustable sights. If you can find one, I'd recommend a Model 14 - 6" barrel, .38 Special, and an old-school target pistol from the days when revolvers ruled the ranges. N-frame Model 28s and 27s are very accurate but a bit heavy for one-handed shooting...ask me how I know!
     

    Melnic

    Ultimate Member
    MDS Supporter
    Dec 27, 2012
    15,282
    HoCo
    It depends what kind of shooting you plan to do with it. I can tell you that you probably won't shoot too many .357 mags one handed before you realize that it isn't fun.

    If you plan to shoot paper, maybe you should look for a S&W Model 14. They are K frame revolvers and have been known for their accuracy. If you still want to shoot .357 periodically, then look for a six inch Model 686.

    Ruger GP revolvers are great utility guns but they aren't target pistols.

    Punching paper or shooting steel. I'd prefer a mild pet load tuned for accuracy and not energy.
     

    Magnumite

    Ultimate Member
    Dec 17, 2007
    6,561
    Harford County, Maryland
    For one handed, you might want to skip nose-heavy weight of the underlug, with something like this:
    https://ruger.com/products/gp100/specSheets/1768.html

    Maybe :shrug:

    In terms of trigger jobs, aren't Rugers supposed to tune themselves by dry firing the dickens out of them?

    That is the characteristic of stainless components. I have been shooting Ruger revolvers for 40 years. They may smooth out some but they don’t tune themselves. Stones and knowing where to go in the action produces good pulls.
     

    Users who are viewing this thread

    Latest posts

    Forum statistics

    Threads
    274,921
    Messages
    7,259,069
    Members
    33,349
    Latest member
    christian04

    Latest threads

    Top Bottom